Scorpion film behaves like any quality 1.5 mil dual-ply automotive film: it rewards clean glass, controlled heat and patience. These tips come from our own Scorpion lessons on YouTube and the order we teach in class. Use them as a refresher, not a replacement for hands-on training or Scorpion's own instructions.
New to the lineup? Read Scorpion window film lines explained first to see what Carbon, Carbon Plus, King, Shield and Shield Plus are.
1. Get the Slip Solution Right
Slip solution lets you float the film into position, then squeegee the water out so the adhesive grabs. Too much soap and the film slides around and takes longer to tack. Too little and it grabs before you're ready. Mix it the same way every time. Our 8-pump rule for baby shampoo slip solution shows the exact mix we use.
2. Clean Like the Install Depends On It (It Does)
Most of what customers call "bubbles" is dirt. Scrape and squeegee the inside of the glass, clean the gasket edges and wipe down the door panel so nothing drips onto the film. On frameless glass, trick the door latch so the window stays up and you don't get a gap at the bottom.
3. Set Up the Film Before You Shrink
Curved glass needs the film shaped to it. Lay the film on the outside of the glass with the liner facing out, anchor it and spread the "fingers" (the loose areas) evenly before you put any heat on it. In the video above, we show how to position Scorpion film so the fingers shrink down without creasing.
4. Shrink With Control
Move the heat gun steadily, shrink each finger a little at a time and press it down with a hard card as it lays flat. Overheating one spot can haze or burn the film. Rear windshields are the hardest, so practise them most. Here's Adam shrinking a full back window with Scorpion Carbon Plus:
5. Use the Factory Edge on Door Glass
On roll-down windows, line the factory edge of the film up with the bottom of the glass, and trim the top and sides on the outside. That gives you a straight, clean bottom edge. In our Porsche 911 frameless lesson, we cut Scorpion 35 Carbon this way before shrinking it on the outside of the glass.
6. Tuck Your Corners in Two Stages
Install the top section first with the window slightly down, then raise the glass and lower it again to tuck the bottom edge behind the seal. Keep the corners wet and clean as you go. The two-stage tuck is one of the four tips in the video at the top of this post.
7. Squeegee in Two Passes, Then Seal the Edges
Start with a light pass to set the film, then go back with full pressure to push out the water. Finish by running a hard card wrapped in microfiber along the edges to seal them. On frameless glass, close the door carefully so you don't catch the fresh edge.
8. Let a Plotter Do Repeat Cuts
Hand-cutting is a core skill, but cutting the same vehicles every week wastes time and film. Scorpion's SCAN app gives you vehicle patterns from your phone or tablet and sends them to a compatible plotter. Read how Scorpion SCAN helps automate a tint shop to see how it fits a shop workflow.
Why Learn on Scorpion Film?
We recommend Scorpion to our students because we find it installer-friendly: easy to handle, shrink and install, which helps new tinters build confidence and get cleaner results. Reading tips only gets you so far, though. Shrinking and tucking click when an instructor is watching your hands. Our 2-day hands-on window tint course starts with roll-down windows on Day 1 and moves to rear windows and heat shrinking on Day 2, in cities across Canada and the USA.
Call or text: Canada 289-201-2070 · USA 321-364-9518
Frequently Asked Questions
Is Scorpion window film easy to install?
We recommend Scorpion to our students partly because we find it installer-friendly: easy to handle, shrink and install. Adam calls Carbon Plus the film he'd want a beginner to use on a back window. Any film still needs clean glass, the right slip solution and good technique.
What slip solution should I use with Scorpion film?
Use a consistent mix of water and a gentle soap such as baby shampoo. Too much soap or too little both cause problems with positioning and adhesion. Our 8-pump rule post explains the mix we teach.
Do you shrink Scorpion film on the outside of the glass?
Yes. Like other automotive films, you shape it on the outside of the glass with a heat gun so it matches the curve, then install it on the inside. Our videos show this on rear windshields and on frameless Porsche door glass.
How do I stop the bottom corners lifting on roll-down windows?
Use a two-stage install. Place the film, then lower the window and tuck the bottom edge under the seal, keeping the corners clean and free of contamination. Our tips video shows the tuck.
Can I cut Scorpion film with a plotter?
Yes. Scorpion's SCAN app gives you vehicle patterns from your phone or tablet and sends them wirelessly to a compatible plotter. Hand-cutting is still worth learning, but plotters save film and time on repeat vehicles.
Ready to learn it hands-on? See all upcoming window tint classes or call or text us: Canada 289-201-2070 · USA 321-364-9518.
Share and get 15% off!
Simply share this product on one of the following social networks and you will unlock 15% off!